INSTALLATION INSTRUCTIONSInstrucciones de instalaciónInstallationsanleitungInstruções de InstalaçãoIstruzioni di installazioneInstallatie-instructiesI
KWT-110 Installation Instructions10Site Requirements for Using Steel StudsWARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIO
Installation Instructions KWT-11011Wall Mounting Using Steel Studs or DrywallAfter determining the site meets the installation requirements:1. Identi
KWT-110 Installation Instructions12Figure 12Mounting CPU to WallCAUTION: Overtightening screws may cause wall bracket to compress into soft wall sur
Installation Instructions KWT-11013Figure 154. Drill three 7/64" holes. (See Figure 15)5. Install three #12 x 2 1/2" round pan wood screws
KWT-110 Installation Instructions142. Drill six 1/2" holes at locations marked in Step 1. (See Figure 18)3. Hold metal channel on anchor (K) fla
Installation Instructions KWT-11015Horizontal Installation using Wood StudsNOTE: Wall track accessory may be mounted horizontally to two studs that
KWT-110 Installation Instructions16Site Requirements for Steel StudsWARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PER
Installation Instructions KWT-11017Vertical Installation using Steel StudsAfter determining the site meets the installation requirements:1. Identify
KWT-110 Installation Instructions18WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPME
Installation Instructions KWT-11019Figure 319. Snap off plastic straps on anchor at wall by pushing side to side, snapping off straps level with flan
KWT-110 Installation Instructions2DISCLAIMERMilestone AV Technologies, and its affiliated corporations and subsidiaries, (collectively, Milestone) in
KWT-110 Installation Instructions20Figure 352(J) x 2(V) x 2(N) x 2(H)132. Reinstall side cover to wall track accessory after locking plate brackets h
Installation Instructions KWT-110217. Use 5/32" hex driver (AA) to tighten set screw in bottom of wall mount. (See Figure 37)NOTE: Ensure set s
KWT-110 Installation Instructions22Figure 403. Use 1/8" hex key (BB) to install #10 button head cap screws (V) through #10 washers (N) and wall
Installation Instructions KWT-11023Figure 42Cable Management - Keyboard Tray1. Thread keyboard cable through one of two holes along the back edge of
KWT-110 Installation Instructions24 Figure 46KEYBOARD TRAY ADJUSTMENTSSwing ArmPivot/Swing1. Using 3/16" hex key (Z), slightly loosen or tighten
Installation Instructions KWT-11025screws ONLY as necessary to allow installation of Centris bracket!1. Ensure Centris bracket is able to swivel and
KWT-110 Installation Instructions26Figure 533. Close cable management bracket by sliding it back towards the centerline of the arm.NOTE: If necessar
Installation Instructions KWT-11027Figure 57Centris Head1. If previously attached, disconnect cables from display, then remove display.2. Using Phill
KWT-110 Installation InstructionsUSA/International A8401 Eagle Creek Parkway, Savage, MN 55378P800.582.6480 / 952.894.6280F877.894.6918 / 952.894.691
Installation Instructions KWT-1103Dimensions"X"COMPONENTMOUNTING BRACKETBRACKETMINIMUM DISTANCE BETWEEN COMPONENT MOUNTING BRACKETS IN HORI
KWT-110 Installation Instructions4DIMENSIONS5.631435.6714410.5726810.0[254]1.30336.501651.6341LIFT ARM13.25" VERTICAL RANGE 2.36RETRACTED6019.45
Installation Instructions KWT-1105LEGENDTighten FastenerApretar elemento de fijaciónBefestigungsteil festziehenApertar fixadorSerrare il fissaggioBev
KWT-110 Installation Instructions6TOOLS REQUIRED FOR INSTALLATIONPARTS7/64"#217/64"1/2" 1/4"(included)1/8"(included)3/16&quo
Installation Instructions KWT-1107PARTS - CONTINUEDM(6)N(6)P(4) Q(4)R(6)S(4)T(4)U(4)V(6)W(4) X(8)Y(1)Z(1)AA(1)BB(1)#101/2 x .194 x 3/4"1/2 x .19
KWT-110 Installation Instructions8ASSEMBLY AND INSTALLATION - CPU MOUNTInstallation of Protective Rubber Edging1. Place four strips of protective rub
Installation Instructions KWT-11096. Use adjustment knobs to compress mount around CPU until CPU is tightly secured within mount (D). (See Figure 5)F
Comments to this Manuals